FSC 9310 JCP A120 50% LAID-ANTIQUE BOOK Printing Paper February 1, 1999 -------------------------------------------------------------------------- Use information: The paragraph is information only and is not exclusively definitive of the end use. For multicolor face and back offset printing of pamphlets, brochures, invitations, programs, etc., requiring attractive appearance and/or above average durability and above average permanence. Has a rough, soft finish with decorative chain marks running at right angles to laid lines. High bulk. Printed matter may include text, line illustrations, and halftones up to 150-line screen. Stock: Not less than 50 pct cotton or linen fibers. Groundwood pulp, not to exceed 1 pct. No fluorescent (optical) brighteners shall be added to the pulp or paper during manufacture. Fluorescence, due to residual white water, broke, or natural fibers, is permissible; provided the increase in reflectance, measured with and without the ultraviolet component of a light source of 3100 kelvin in combination with a C.I.E. (International Commission on Illumination) Z (blue) filter, does not exceed 2.0 pct. Note: \1\ Postconsumer recovered fiber, in any percentage, is encouraged, provided that the requirements of this Standard are met. Acidity: pH value shall average not less than 6.5. Grammage (g/m\2\)................................. 105 Basis weight: 25 by 38 inches, 500 sheets (pounds).......................................... 70 A tolerance of5 pct shall be allowed. Bursting strength: Average, not less than (kPa)... 130 Equivalent (lb/in\2\)........................... 19 Opacity: Average, not less than (percent)......... 90 No individual specimen shall average less than (percent)....................................... 88 Thickness: Average (mm)........................... 0.140 Equivalent (inch)............................... 0.0055 A tolerance of 0.013 mm (0.0005 inch) shall be allowed. Paper shall be uniform and shall not vary more than 0.011 mm (0.0004 inch) from one edge to the other. Chain marks: Shall run parallel to machine direction of the sheet and match the standard sample. General appearance: Paper shall conform to the standard sample(s) adopted by the Government. Color: The paper in the order (or publication) shall be uniform with a target brightness of 72 pct 2 pct or as specified. The color variation shall not exceed DE(CIELAB)=1.0. Finish: Paper shall have a laid-finish. Formation: Shall be uniform. Cleanliness: The dirt count for each side of the paper shall not exceed 250 specks per square meter. No sample sheet (600 to 650 cm\2\ in size) shall contain more than one defect with an equivalent area of 0.25 mm\2\ or greater. Sampling and testing: Shall be conducted in accordance with standards in Part 2, Government Paper Specification Standards. ------------------------------------------------------------------------ Unless otherwise specified, the following is automatically waived when printing or duplicating is to be accomplished on commercial contract Sizing: Paper shall be surface- and internal-size suitable for satisfactory printing on both sides of the paper on high-speed offset presses equipped with continuous flow or brush dampening systems. Color: Shall match the Government's standard sample for color. A deviation of DE(CIELAB)=3.0 from the color standard is allowed. For information only, the CIELAB values (Ill D65, 10 deg. observer) of the color standard are L*=93.0 a*=-0.5 b*=7.5 Curl: Paper shall lie flat with either no tendency to curl or with a curl which can be overcome under reasonable working conditions. Surface: Shall be free from lint fuzz, or any particles which will pick, lift, fluff, or pile on the blanket under normal press conditions. Size and trim: Sheets: Paper shall be furnished in the size(s) ordered and shall be flat, trimmed square on four sides with clean smooth edges, and evenly jogged. A tolerance of 2 mm (\1/16\ inch) shall be allowed except for sheets 216 by 356 mm (8\1/2\ by 14 inches) or less; then a tolerance of 1 mm (\1/32\ inch) shall be allowed. Successive sheets within any package shall not differ from each other by more than 0.5 mm (\1/64\ inch). Paper with the long dimension 813 mm (32 inches) or less shall be considered square if the variation does not exceed 1 mm (\1/32\ inch); over 813 mm (32 inches); 1.588 mm (\1/16\ inch). Grain: Direction of the grain of flat paper shall be as ordered. Pressroom conditions: The bulk of this paper will be used in air- conditioned pressrooms maintained at 24 deg.C 2 deg.C and 45 pct 8 pct relative humidity. --------------------------------------------------------------------------- \1\ This grade is typically a low Government usage paper and currently not readily and/or economically available with postconsumer recovered fiber content. If a postconsumer recovered fiber content is desired in the paper, that number will be stated in the procurement document. Note, recovered material (cotton/linen) is not a postconsumer recovered fiber.