FSC 7530 JCP G50
25% TRANSLUCENT BOND
Bond Paper February 1, 1999
--------------------------------------------------------------------------
Use information: This paragraph is informational only and is not
exclusively definitive of the end use.
For offset printing, generally face only, of open master forms, etc.,
which are used for duplicating in the ammonia process of reproduction.
Printed matter may include text and line illustrations.
Stock: Not less than 25 pct cotton or linen fibers. Groundwood pulp, not
to exceed 1 pct.
Note: \1\ Postconsumer recovered fiber, in any percentage, is
encouraged, provided that the requirements of this Standard are met.
Acidity: pH value shall average not less than 5.0.
Rosin: Average not to exceed 2.0 pct for papers having pH value less
than 6.5.
Grammage (g/m2)........................ 60
Basis weight: 17 by 22 inches, 500 sheets
(pounds).......................................... 16
A tolerance of 5 pct shall be allowed.
Folding endurance: Average, each direction, not less than--
M.I.T. (double fold)............................ 75
Schopper (double fold).......................... 75
Opacity: Average, not to exceed (percent)......... 70
Note: The paper should freely transmit ultra-violet light in near
visible portion of the spectrum. It should retain its ultra-violet
light transparency with age, remaining free from that degree of
discoloration which would materially reduce its printing speed. If
treated to aid transparency, the materials used shall not cause
bleeding or feathering of the image nor offsetting in the files.
Ruling and writing qualities: Lines ruled and characters written with
ball point and felt tip pens shall be clear cut and free from
excessive feathering.
Erasing quality: Paper shall retain good ruling, writing, and typing
quality, texture, and surface appearance, without ink spreading after
repeated erasures. Samples from the delivery shall show no greater
resistance than the standard sample to removal by abrasion of
typewritten characters.
Watermark: Paper shall not be watermarked.
Curl: Paper shall lie flat before and after processing through a high
speed copier or laser printer with either no tendency to curl or with
a curl which can be overcome under reasonable working conditions.
General appearance: Paper shall conform to the standard sample(s)
adopted by the Government.
Color: The paper in the order (or publication) shall be uniform with a
target brightness of 80 pct. The color variation shall not exceed
DE(CIELAB)=1.0.
Finish and formation: Shall be uniform.
Cleanliness: The dirt count for each side of the paper shall not
exceed 250 specks per square meter. No sample sheet (600 to 650 cm\2\
in size) shall contain more than one defect with an equivalent area of
0.25 mm\2\ or greater.
Sampling and testing: Shall be conducted in accordance with standards in
Part 2, Government Paper Specification Standards.
------------------------------------------------------------------------
Unless otherwise specified, the following is automatically waived when
printing or duplicating is to be accomplished on commercial contract
Equilibrium relative humidity: Shall be 45 pct 8 pct at
23 deg.C 2 deg.C.\2\
Sizing: Paper shall be surface- and internal-sized suitable for
satisfactory printing on both sides of the paper on high-speed offset
presses equipped with continuous flow or brush dampening systems.
Color: Shall match the Government's standard sample for color. A
deviation of DE(CIELAB)=3.0 from the color standard is allowed.
Surface: Shall be free from lint, fuzz, or any particles which will
pick, lift, fluff, or pile on the blanket under normal press
conditions. Paper shall lie flat with either no tendency to curl or
with a curl which can be overcome under reasonable working conditions.
Size and trim: Sheets: Paper shall be furnished in the size(s) ordered
and shall be flat, trimmed square on four sides with clean smooth
edges, and evenly jogged. A tolerance of 2 mm (\1/16\
inch) shall be allowed except for sheets 216 by 356 mm (8\1/2\ by 14
inches) or less; then a tolerance of 1 mm (\1/32\ inch)
shall be allowed. Successive sheets within any package shall not
differ from each other by more than 0.5 mm (\1/64\ inch). Paper with
the long dimension 813 mm (32 inches) or less shall be considered
square if the variation does not exceed 1 mm (\1/32\ inch); over
813 mm (32 inches), 2 mm (\1/16\ inch).
Grain: Direction of the grain on flat paper shall be as ordered.
---------------------------------------------------------------------------
\1\ This grade is typically a low Government usage paper and
currently not readily and/or economically available with postconsumer
recovered fiber content. If a postconsumer fiber content is desired in
the paper, that number will be stated in the procurement document. Note,
recovered material (cotton/linen) is not a postconsumer recovered fiber.
\2\ This requirement may be waived when so stated in the procurement
document. If waived, the following is applicable: Pressroom conditions:
The bulk of this paper will be used in air-conditioned pressrooms
maintained at 24 deg.C 2 deg.C and 45 8 pct
relative humidity.