FSC 9310 JCP P20
HIGH-FINISH FOLDER STOCK, NATURAL AND COLORED
Tag Board February 1, 1999
--------------------------------------------------------------------------
Use information: This paragraph is informational only and is not
exclusively definitive of the end use.
For face and back offset printing of file folders, etc., requiring
strength and durability. Printed matter may include text, line
illsutrations, and solid reverses.
Stock: 100 pct sulphate pulp.
Note: Not less than 30 pct postconsumer fiber. Any percent over 30
percentage points, is encouraged, provided that the requirements of
this Standard are met.
Grammage (g/m 2).................... 170 245 270 405
Basis weight: 24 by 36 inches, ...
500 sheets (pounds)............... 105 150 165 250
A tolerance of 10 pct shall be allowed....................
Thickness: Average (mm)............. 0.20 0.28 0.35 0.45
Equivalent (inch)................. 0.008 0.011 0.014 0.018
A tolerance of 0.025 mm (0.001 inch) shall be allowed.....
Stiffness: Gurley, average, not less than--
Machine direction (mg)............ 2,000 5,000 6,000 14,000
Cross direction (mg).............. 800 1,500 2,000 7,500
Tearing strength: Average, not less than--
Machine direction (mN)............ 1,470 2,450 3,430 3,920
Cross direction (mN).............. 1,960 2,940 3,920 4,900
Equivalent--
Machine direction (grams)......... 150 250 350 400
Cross direction (grams)........... 200 300 400 500
Ruling and writing qualities: Lines ruled and characters written with
pen and ink shall be clear cut and free from excessive feathering.
General appearance: The color, finish, and cleanliness shall conform to
the standard sample(s) adopted by the Government.
Color: The color of the paper/board in the order (or publication)
shall be as specified uniform with color variation not to exceed
DE(CIELAB)=1.0.
For colored stock, paper/board shall match the one of the
established standards or specified by the agency. The commercial color
standard is applicable, unless specified that the color shall conform
to the Government standard. Colors shall not fade or transfer (rub
off) and shall appear even and uniform on the surface of the paper/
board.
Sampling and testing: Shall be conducted in accordance with standards in
Part 2, Government Paper Specification Standards.
------------------------------------------------------------------------
Unless otherwise specified, the following is automatically waived when
printing or duplicating is to be accomplished on commercial contract
Sizing: Paper/board shall be surface- and internal-sized suitable for
satisfactory printing on both sides of the board on high-speed offset
presses equipped with continuous flow or brush dampening systems.
Curl: Paper/board shall lie flat with either no tendency to curl or with
a curl which can be overcome under reasonable working conditions.
Surface: Shall be free from lint, fuzz, or any particles which will
pick, lift, fluff, or pile on the blanket under normal press
conditions.
Size and trim: Paper/board shall be furnished in the size(s) ordered and
shall be flat, trimmed square on four sides with clean
smooth edges, and evenly jogged. A tolerance of 2 mm (\1/
16\ inch) shall be allowed. Successive sheets within any package shall
not differ from each other by more than 0.5 mm (\1/64\ inch). Paper/
board with the long dimension 813 mm (32 inches) or less shall be
considered square if the variation does not exceed 1 mm (\1/32\ inch);
over 813 mm (32 inches), 2 mm (\1/16\ inch).
Grain: Direction of the grain on flat paper/board shall be as ordered.
Pressroom conditions: The bulk of this paper/board will be used in air-
conditioned pressrooms maintained at 24 deg. C 2 deg. C
and
45 pct 8 pct relative humidity.