By Doug Ellison

Follow the excitement as NASA prepares to land, Curiosity, its most technically advanced rover ever on Mars. JPL Visualization Producer Doug Ellison shares live, behind-the-scenes action from the mission control room at NASA’s Jet Propulsion Laboratory in Pasadena, Calif..

TOUCHDOWN

Monday, August 6, 2012 1:13:26 AM

Welcome to Gale Crater. “Adam…you’re a genius!” I shout to Adam Steltzner. He pauses. Stops. Turns around. “I’m not a genius — I just work with a team of them.”

Thanks for the ride

Sunday, August 5, 2012 10:04:10 PM

The EDL Phase Lead, Adam Steltzner, has just thanked the cruise team for their 350-million-mile ride. “Curiosity is in fantastic shape, she’s here because you guys got her here. See you on Mars.”

Go Curiosity. And break out the peanuts.

Mars really has us now.

Sunday, August 5, 2012 10:03:56 PM

Ten thousand and sixty three. Sixty four. Sixty five. As quick as you can count it, our speed towards Mars is accelerating.

Mars is about half the diameter of Earth, but only about 10 percent as heavy as Earth. Even so — on its surface, gravity is about 38 percent that of Earth. In the next 28 minutes, we will gain another 3,000 miles per hour until Curiosity, heatshield ready, slams into the top of the Martian atmosphere.

40 billion to 1

Sunday, August 5, 2012 9:15:28 PM

A quiet approach to Mars as we watch a tiny plot of a graph. The X-band frequency that Curiosity is currently transmitting is a frequency of more than 8 Gigahertz — 8 billion cycles per second. As it rotates, that tiny little graph shows that frequency moving up and down, by about 0.2 Hz. One part in 40 billion. That little bounce up and down is the rotation of the spacecraft, two revolutions per minute. We have that accuracy because we’re bouncing a radio signal from the ground, up to spacecraft and back again. But that signal, after a final poll, will be going away.

Systems Go. Power Go. Thermal Go. Propulsion Go. Nav Go. Uplink Go. Avionics Go. Flight. Software Go. Fault Protection Go. Chief Engineer Go. EDL FLight System Go. Data Management Go. GDS Go. Telecom Go. ACS Go. EDL Activity Lead Go. ACE Go.

“You are clear to bring down the uplink.” So in just over 13 minutes time, Curiosity will no longer have that amazing signal to bounce back - and our little squiggly 1-in-40-billion line will be gone. We will just hear the spacecraft’s own transmitter from more than 150 million miles.

Curiosity is truly on her own.

A Final Check

Sunday, August 5, 2012 8:44:21 PM

This full poll of the flight team is a lengthy and exhaustive tour of the rover, the cruise stage and all the systems. My favorite call is from the chief engineer:

“We are green across the board”

That’s the word from Rob Manning — a veteran of four successful Mars landings. When Rob says things are green, you know you’re in good shape. If you were hoping to spend some time exploring the martian moon Deimos on your way to Gale Crater — please alight the rover now, we just crossed its orbit. Now there are 16,000 miles to go.

Calm before the Storm

Sunday, August 5, 2012 8:32:58 PM

Things got a little quiet in the control room. People heading out for some food before we get down to the business of landing on Mars. It takes huge team to watch over a spacecraft as complex, and activites and intricate as a Mars landing. As they get back to their consoles, they do a comm check to make sure they can all hear each other. Systems. Power. Thermal. Prop. Nav. Uplink. Flight Software. Fault Protection. EO Team Chief. GDS. Telecom. EDL Comm. ACS … the calls, and acronyms, go on and on. Now they are all back on console, the whole team is about to do a full system poll.

Can you hear me?

Sunday, August 5, 2012 7:59:37 PM

Between now and landing, Curiosity will use a total of eight antennas. The Deep Space Network is now listening to a medium-gain antenna transmitting on X-Band on the cruise stage. During entry, two low gain antennas on the back of the spacecraft continue that signal of “tones.” There are also low-gain antennas on the descent stage and the rover. However, Earth will have set at this time.

Meanwhile, a UHF antenna on the backshell, followed by another on the descent stage and finally one on the rover, will continue to transmit telemetry during landing. This data will be received by Mars Odyssey and Mars Reconnaissance Orbiter. Odyssey will relay it straight to Earth so we can track landing. Mars Reconnaissance Orbiter records everything it hears and sends it back a few hours later. Mars Express will also record just the pitch of this signal as a final backup.

The ground stations at the Canberra, Australia Deep Space Communications Complex will follow us the whole way — direct from the rover ’til Earth sets behind it — and from Odyssey and Mars Reconnaissance Orbiter as well. All the way to the ground, a complex system of systems will be trying to keep that tenuous link between Earth and Mars alive.

Nominal!

Sunday, August 5, 2012 5:58:00 PM

“Nominal” sounds like a very boring word, but in the world of spaceflight, nominal is engineer for “awesome.” Thanks to the Deep Space Network, we know just how nominal everything is. Deep Space Station 43, a 70-meter-diameter antenna in Tidbindilla, Austraila is currently receiving a steady stream of data at 2,000 bits per second that informs the engineers how all their subsystems are doing. Attitude control, thermal performance, power systems, avionics, propulsion, communication, the list is long. The flight team (meet them all here: www.gigapan.com/gigapans/110926) just took a poll, and all subsystems are nominal. The MEDLI instrument is now powered up, and healthy. It’s talking to the flight computer, and the power system can see it drawing just 300 milliamps. It will record first-of-its-kind data on temperature, pressure and other readings through Curiosity’s heatshield during entry. This data will help us understand how the heatshield behaves and can help us make them better for the future. As MEDLI lives on the inside of the heatshield, it is thrown overboard when the heatshield is separated about six miles above the surface. Its data will be safely stored on the rover to be downlinked after landing.

Spin

Sunday, August 5, 2012 1:15:54 PM

When you’re a spacecraft it’s important to know which way you’re facing. If you know which way you’re facing, you know which way Earth is, so you can talk to home; which way the sun is, so you can get power on a solar array; and if you’re Curiosity, you know which way Mars is. There are two ways spacecraft typically orient themselves. One is called “three-axis stabilized,” which means the spacecraft uses thrusters and reaction wheels to keep itself pointed the right way. You may have heard about trouble with reaction wheels on the Mars Odyssey orbiter recently (it carries a spare just in case, and we’re now using it). Curiosity (as well as its older sisters Spirit and Opportunity, and Juno right now on its way to Jupiter) just spin their way through deep space. They point in one direction and spin, like a top. That spin stops the spacecraft wandering off and pointing somewhere else. Curiosity, all the way till after we wave goodbye to its cruise stage about 17 minutes before landing, spins at 2 rpm. During its 253-day cruise, Curiosity will have spun more than 720,000 times. It’s enough to give a rover a headache.

Three Degrees

Sunday, August 5, 2012 1:05:01 PM

I’ve arrived “on lab” (JPL-speak for “at the office”) to check up on our computer running Eyes on the Solar System (http://eyes.nasa.gov) that will be fed to NASA Television tonight. Looking up in the control room — I see we’ve just crossed 80,000 miles to go. Less than four- times the distance from Earth to our geostationary communication satellites. Mars is about 4,200 miles in diameter - so with a little high school trig, we can calculate that Mars would appear 3 degrees across to Curiosity. That’s six times larger than the size of the full moon from Earth. This time yesterday, Curiosity was only 170 mph slower than it is now. In the next 10 hours as it falls to Mars it gains another 5,000. As an astronaut onboard Apollo 13 said to mission control on their way home, “The world’s getting awful big in the window.”

The Runners Up

Friday, August 3, 2012 11:15:00 AM

Adam Steltzner (MSL EDL phase lead) is a great speaker and real highlight of today’s NASA Social event. A fantastic question from the audience asked what ideas for landing Curiosity were rejected.

The runner-up: airbags. There isn’t a fabric that we know of strong enough to handle the impact loads that a 899-kg rover would create. Good enough for the 180-kg of Spirit and Opportunity, but it just can’t get scaled up to something as big as Curiosity.

Third place: Put the rover on top of the rockets. The problem there is that the rover is so heavy, and the propellant tanks so large, that you would have a very tall vehicle prone to toppling over on touchdown.

It may look a little crazy — but the skycrane actually makes a lot of sense.

Speed Up, Slow Down

Thursday, August 2, 2012 5:12:47 PM

The art of flying between the planets is a balancing act of gravity, velocity, trajectory and timing. These variables come to a thrilling climax on Sunday evening as Curiosity reaches the Red Planet.

Launched into a trajectory around the sun in November 2011, Curiosity is currently in a solar orbit that just reaches the orbit of Mars. That trajectory means that, from the perspective of the sun, by noon Pacific time on August 1 Curiosity was travelling at 47,500 miles per hour. Yet Mars is travelling at more than 53,000 mph — some 5,500 mph faster than Curiosity. Left alone, Curiosity would soon begin a slow cruise back towards the orbit of Earth, while Mars would carry on along its own, faster trajectory.

But breathtaking accuracy by the navigation team guiding Curiosity means that Mars will be at the right place Sunday to pick up Curiosity. The planet’s gravity will speed up the spacecraft by 13,000 mph (as viewed from the sun) until their speeds match and Curiosity is safely on the surface. On the freeway of interplanetary navigation, Curiosity is the bug, and Mars is the windshield. To get ready for a martian year of exploration, you’ve got to take a big hit.

Welcome to the Landing Blog

Thursday, August 2, 2012 5:12:16 PM

Welcome to the Curiosity landing blog. I’m Doug Ellison, a visualization producer here at JPL. Our group is responsible for many of the graphics you will see that show how Curiosity has made its way to Mars, and what it will do when it gets there.

The landing animation was a nine-month-long project of obsessing over details of every piece of the spacecraft and its adventure. We’ve launched a special version of Eyes on the Solar System at http://eyes.nasa.gov that lets you ride with Curiosity all the way to the surface. We’ve become so familiar with the spacecraft and what it does that we even surprise the mission team themselves sometimes!

On landing night, I’ll be in our mission control (the “Dark Room”) keeping you up to date with some of the goings-on as Curiosity approaches Mars. Until then I’ll post a few little factoids about Curiosity, its trip to Mars, and its epic landing at Gale Crater.

By Julie Cooper

Each month in “Slice of History” we feature a historical photo from the JPL Archives. See more historical photos and explore the JPL Archives at https://beacon.jpl.nasa.gov/.

Free Fall Capsule Drop Test — Photograph Number 354-595

In 1961, a drop capsule was developed at NASA’s Jet Propulsion Laboratory in Pasadena, Calif., by Section 354, Engineering Research. It was an experimental chamber to study how liquids behave in free-fall (zero gravity). The prototype capsule was dropped from a helicopter hovering at 800 feet, but the capsule was found to be too unstable for these tests. In September 1962, a trial drop was done from the Bailey bridge that connected JPL to the east parking lot. Testing was then moved to a bridge crossing Glen Canyon near Page, Arizona. The dam was under construction at the time and provided a 672-foot-fall with a soft dirt impact area.

The 204 pound shell contained a high-impact sequence camera designed for this experiment, a stopwatch, a liquid sample and a release mechanism. Three external motion picture cameras with different focal lengths looked down on the capsule as it fell. Although the capsule fell for about 10 seconds without rolling, pitching or yawing, there were problems with the internal release mechanism. It appears the experiment was discontinued after two attempts.

This post was written for “Historical Photo of the Month,” a blog by Julie Cooper of JPL’s Library and Archives Group.

By Duane Roth

Cassini Has a Special View of Saturn These Days - How Did It Get There?

For the past 18 months, NASA’s Cassini spacecraft has been orbiting Saturn in practically the same plane as the one that slices through the planet’s equator. Beginning with the Titan flyby on May 22, navigators started to tilt Cassini’s orbit in order to obtain a different view of the Saturnian system. The measure of the spacecraft orbit’s tilt relative to Saturn’s equator is referred to as its inclination. The recent Titan flyby raised Cassini’s inclination to nearly 16 degrees. Seven more Titan flybys will ultimately raise Cassini’s inclination to nearly 62 degrees by April 2013. On Earth, an orbit with a 62-degree inclination would pass as far north as Alaska and, at its southernmost point, skirt the latitude containing the tip of the Antarctic Peninsula.

These graphics show the orbits NASA’s Cassini spacecraft has made and will make around the Saturn system from September 2010 to April 2013. As shown in gray, Cassini orbited within the plane of Saturn’s equator during the first 18 months of its current mission phase, known as the Solstice mission. Then, starting in May 2012, Cassini used the gravity of Saturn’s largest moon, Titan, to tilt its orbit as shown in the magenta loops, reaching a maximum tilt of about 62 degrees in April, 2013. Titan’s orbit is shown in red. The orbits of Saturn’s inner moons are shown in black. Image credit: NASA/JPL-Caltech

You may wonder why this change has been planned and how this feat is achieved. The “why” is to allow scientists to observe Saturn and the rings from different geometries in order to obtain a more comprehensive three-dimensional understanding of the Saturnian system. For instance, because Saturn’s rings lie within Saturn’s equatorial plane, they appear as a thin line when viewed by Cassini in a near-zero-degree orbit inclination. From higher inclinations, however, Cassini can view the broad expanse of the rings, making out details within individual ringlets and helping to unlock the secrets of ring origin and formation. Some of those images have already started to come in.

At higher inclinations, Cassini can also obtain excellent views of Saturn’s poles, and measure Saturn’s atmosphere at higher latitudes via occultation observations, where radio signals, sunlight or starlight received after passing through the atmosphere help to determine its composition and density.

The “how” is by using the gravity of Titan — Saturn’s largest moon by far — to change the spacecraft’s trajectory. Like the rings and Cassini’s previous orbit, Titan revolves around Saturn within a plane very close to Saturn’s equatorial plane. As Cassini flies past Titan, Titan’s gravity bends the spacecraft’s path by pulling it towards the moon’s center — similar to a ball bearing rolling on a smooth horizontal surface past a magnet. Near Titan, the motion is confined to a plane containing the spacecraft’s path and Titan’s center of mass. If this “local” plane coincides with Cassini’s orbital plane about Saturn, the trajectory’s inclination will remain unchanged. However, if this plane differs from Cassini’s orbital plane about Saturn, then the bending from Titan’s gravity will have a component out of Cassini’s orbital plane with Saturn, and this will change the tilt of the spacecraft’s orbit. Repeated Titan flybys will raise Cassini’s orbit inclination to nearly 62 degrees by April of next year and then lower it back to the Saturn equatorial plane in March 2015.

NASA’s Cassini spacecraft has recently resumed the kind of orbits that allow for spectacular views of Saturn’s rings. This view, from Cassini’s imaging camera, shows the outer A ring and the F ring. The wide gap in the image is the Encke gap, where you see not only the embedded moon Pan but also several kinky, dusty ringlets. A wavy pattern on the inner edge of the Encke gap downstream from Pan and a spiral pattern moving inwards from that edge show Pan’s gravitational influence. The narrow gap close to the outer edge is the Keeler gap. Image credit: NASA/JPL-Caltech/SSI

Gravity assists are key to Cassini’s ever-changing orbital geometries. Onboard propellant alone would quickly become depleted attempting to accomplish these same changes. A gravity assist can be characterized by the amount of “delta-v,” or change in the velocity vector, it imparts to a spacecraft. Delta-v may of course also be imparted to the spacecraft via rocket engines and, either way, alters the spacecraft’s orbit. The eight Titan gravity assists responsible for raising Cassini’s inclination to 62 degrees will provide a delta-v of 15,000 mph (6.6 kilometers per second). For comparison, Cassini’s rocket engines had only enough propellant after initially achieving orbit around Saturn to deliver about 2,700 mph (1.2 kilometers per second) of delta-v. That’s 15,000 mph of capability spread over 11 months via gravity assists versus a modest 2,700 mph of capability spread over more than 13 years via rocket engines! Because delta-v is a vector, it may change both the speed and direction of Cassini at a point along its orbit, so the speed of Cassini is not changing by 15,000 mph, but mostly all of the directional changes sum to 15,000 mph. To give these values some context, Cassini’s speed typically varies between as low as 2,500 mph (1.1 kilometers per second) and as high as 79,000 mph (35 kilometers per second) relative to Saturn between apokrone and perikrone, the farthest and closest points from Saturn along its orbit. Gravity assists from the initial prime mission Titan flyby in 2004 to the final Solstice Mission Titan flyby in 2017 will provide nearly 200,000 mph (90 kilometers per second) of delta-v, leveraging the onboard propellant by a ratio of 75 to 1. The bulk of the Saturn tour trajectory is shaped by gravity assists, while the role of onboard propellant is to fine-tune the trajectory.

At the end of year 2015, Cassini will again begin climbing out of Saturn’s equatorial plane in preparation for its grand finale. After reaching an inclination of nearly 64 degrees, a Titan gravity assist in April 2017 will change Cassini’s perikrone so that Cassini will pass through the narrow 2,000-mile (3,000-kilometer) gap between Saturn’s atmosphere and innermost ring. Twenty-two spectacular orbits later, one final distant Titan gravity assist will alter Cassini’s course for a fiery entry into Saturn’s atmosphere to end the mission.

By Marc Rayman

As NASA’s Dawn spacecraft investigates its first target, the giant asteroid Vesta, Marc Rayman, Dawn’s chief engineer, shares a monthly update on the mission’s progress.

This image, from NASA’s Dawn spacecraft, shows rock material that has moved across the surface and flowed into a low area in the ridged floor of the Rheasilvia basin on Vesta. The image shows how impacts and their aftermath constantly reshape the landscape. Image credit: NASA/JPL-Caltech/UCLA/MPS/DLR/IDA/PSI

Dear Upside Dawn Readers,

Dawn is now seeing Vesta in a new light. Once again the probe is diligently mapping the ancient protoplanet it has been orbiting for nearly a year. Circling the alien world about twice a day, the ardent adventurer is observing the signatures of Vesta’s tortured history, including the scars accumulated during more than 4.5 billion years in the main asteroid belt between Mars and Jupiter.

Having successfully completed its orbital raising maneuvers to ascend to its second high-altitude mapping orbit (HAMO2), Dawn looks down from about 680 kilometers (420 miles). This is the same height from which it mapped Vesta at the end of September and October 2011. The lifeless rocky landscape has not changed since then, but its appearance to the spacecraft’s sensors has. The first high-altitude mapping orbit (HAMO1) was conducted shortly after southern hemisphere summer began on Vesta, so the sun was well south of the equator. That left the high northern latitudes in the deep darkness of winter night. With its slower progression around the sun than Earth, seasons on Vesta last correspondingly longer. Thanks to Dawn’s capability to linger in orbit, rather than simply conduct a brief reconnaissance as it speeds by on its way to its next destination, the probe now can examine the surface with different lighting.

Much of the terrain that was hidden from the sun, and thus the camera, during HAMO1 is now illuminated. Even the scenery that was visible then is lit from a different angle now, so new observations will reveal many new details. In addition to the seasonal northward shift in the position of the sun, Dawn’s orbit is oriented differently in HAMO2, as described last month, so that makes the opportunity for new insights and discoveries even greater.

The strategy for mapping Vesta is the same in HAMO2 now as it was in HAMO1. Dawn’s orbital path takes it nearly over the north pole. (As we saw last month, the orbit does not go exactly over the poles but rather reaches to 86 degrees latitude. That slight difference is not important for this discussion.) During the ship’s southward passage over the sunlit side, the camera and the visible and infrared mapping spectrometer (VIR) acquire their precious data. After passing (almost) above the south pole, Dawn sails north over the night side. Instead of pointing its sensors at the deep black of the ground below, the probe aims its main antenna to the extremely distant Earth and radios its findings to the exquisitely sensitive receivers of the Deep Space Network. The pattern repeats as the indefatigable spacecraft completes loop after loop after loop around the gigantic asteroid every 12.3 hours.

As Dawn revolves, Vesta rotates on its axis beneath it, turning once every 5.3 hours. Just as in HAMO1, mission planners artfully choreographed this celestial pas de deux so that over the course of 10 orbits, lasting just over five days, the camera would be able to view nearly all of the lit surface. A set of 10 orbits is known to Dawn team members (and to you, loyal readers) as a mapping cycle.

Until a few months ago, HAMO2 was planned to be four cycles. Thanks to the determination in April that Dawn could extend its residence at Vesta and still meet its 2015 appointment with dwarf planet Ceres, HAMO2 has been increased to six mapping cycles (plus even a little more, as we shall see below), promising a yet greater scientific return.

In cycle 1, which began on June 23, the camera was pointed at the surface directly underneath the spacecraft. The same view will be obtained in cycle 6. In cycles 2 through 5, images are acquired at other angles, providing different perspectives on the complex and dramatic landscape. Scientists combine the pictures to formulate topographical maps, revealing Vesta’s full three-dimensional character from precipitous cliffs and towering peaks of enormous mountains to gently rolling plains and areas with mysterious ridges and grooves to vast troughs and craters punched deep into the crust. Knowing the elevations of the myriad features and the angles of slopes is essential to understanding the geological processes and forces that shaped this exotic mini-planet. In addition to the exceptional scientific value, the stereo imagery provides realistic, exciting views for anyone who wants to visualize this faraway world. If you have not traveled there yourself, be sure to visit the Image of the Day regularly and the video gallery occasionally to see what you and the rest of humankind had been missing during the two centuries of Vesta’s appearance being only that of a faint, tiny blob in the night sky.

› Continue reading Marc Rayman’s Dawn Journal

By Marc Rayman

As NASA’s Dawn spacecraft investigates its first target, the giant asteroid Vesta, Marc Rayman, Dawn’s chief engineer, shares a monthly update on the mission’s progress.

On May 3, 2011, the mapping camera on NASA’s Dawn spacecraft captured its first image (left) of the giant asteroid Vesta. Only 5 pixels across, the image didn’t provide any new information about the asteroid, but it was important for navigation purposes and provided an exciting first look at Dawn’s eventual target. About five months later, Dawn snapped the much more detailed image on the right from only 700 kilometers (435 miles) from the surface of Vesta and has since provided unparalleled views of the mysterious world. Image credit: NASA/JPL-Caltech

Dear Readers of all Dawnominations,

Far from Earth, on the opposite side of the sun, deep in the asteroid belt, Dawn is gradually spiraling around the giant protoplanet Vesta. Under the gentle pressure of its uniquely efficient ion propulsion system, the explorer is scaling the gravitational mountain from its low-altitude mapping orbit (LAMO) to its second high-altitude mapping orbit (HAMO2).

Dawn spent nearly five months in LAMO, circling the rocky world at an average altitude of 210 kilometers (130 miles) as it acquired a fabulous bounty of pictures; visible, infrared, neutron, and gamma ray spectra; and measurements of the gravity field. As we saw last month, the probe was far more productive in each investigation than the ambitious team members had expected or had ever dared hope it would be. With that outstanding success behind it, it is looking ahead and up to its work in HAMO2, about 680 kilometers (420 miles) high.

Dawn is the first spacecraft to explore Vesta, the second most massive resident of the main asteroid belt between Mars and Jupiter. Indeed, this is the only craft ever to orbit a body in the asteroid belt. No other missions are currently on the books to visit this remote, exotic world, which is now appreciated to be more closely related to the terrestrial planets (including Earth) than to typical asteroids. And now Dawn is receding from it. On May 1, it began the slow ascent to its next observation orbit. It may well be decades before another robotic ambassador from Earth comes as close to Vesta as this bold traveler has.

Humankind’s first exploration of Vesta has been exceptionally rewarding. A simple measure of that can be seen with just two photographs. More than two centuries after its discovery, this giant asteroid was first glimpsed by the approaching spaceship from Earth on May 3, 2011. From a distance of 1.2 million kilometers (750 thousand miles), or more than three times the separation between Earth and the moon, Dawn’s mapping camera perceived Vesta as only five pixels across. Each pixel spanned more than 110 kilometers (70 miles), revealing nothing new compared to what astronomers’ most powerful telescopes had shown (but the image was of importance for navigation purposes). Nevertheless, at the time, it was tremendously exciting to obtain the first views of a distant, unfamiliar shore after a voyage of more than 2.6 billion kilometers (1.6 billion miles) on the interplanetary ocean. Sighting our first celestial port of call more than three and a half years after this cosmic adventure began was thrilling indeed. But now, with more than 25 thousand spectacular photos in hand from much smaller distances, it is even more gratifying to acknowledge that first picture as one of the worst ever taken of Vesta. The Image of the Day from one year later
was acquired in October 2011 from 1,700 times closer; and most of the images have been obtained from LAMO, about 5,700 times nearer than that first one. Dawn has rapidly transformed Vesta from a mere fleck among the stars into a fascinating, complex and splendidly detailed world.

Keeping the remote vessel on the planned spiraling course from one mapping orbit to another presents the crew with a set of formidable challenges, but this team has accomplished the maneuvers to successively reach survey orbit, the first high-altitude mapping orbit (HAMO1) and LAMO. The current orbital transfer is complex and demanding, but it is proceeding very well. Controllers update the flight profile every few days to ensure the probe stays close to the carefully designed trajectory to HAMO2. To gain a sense of the progress, go here for your correspondent’s atypically succinct weekly summaries of the spiral status.

› Continue reading Marc Rayman’s Dawn Journal

By Julie Cooper

Each month in “Slice of History” we feature a historical photo from the JPL Archives. See more historical photos and explore the JPL Archives at https://beacon.jpl.nasa.gov/.

Something is Missing … — Photograph Number JB-16114B

To anyone who came to NASA’s Jet Propulsion Laboratory in Pasadena, Calif., after 1975, this photo may seem odd – building 264 has only two stories, and there is a large pond running down the middle of the mall.

In September 1970, construction began on building 264, the Systems Development Laboratory, a support facility for the Space Flight Operations Facility in building 230. A 7.5 foot tunnel connected the two buildings, lined with racks to support the cables and wiring that joined them. It was constructed as a two story building with a foundation capable of supporting six additional floors, although JPL had to wait several years for additional funding to be approved. The building was finally completed late in 1975, providing mission support for the Viking and Voyager missions, computer space, and three floors of office space.

The pond was nearly 300 feet long, stretching from the mall fountain to a parking area at the east end of building 183. It was built in 1967 and removed by about 1989, but the fountain remains.

This post was written for “Historical Photo of the Month,” a blog by Julie Cooper of JPL’s Library and Archives Group.

By Julie Cooper

Each month in “Slice of History” we feature a historical photo from the JPL Archives. See more historical photos and explore the JPL Archives at https://beacon.jpl.nasa.gov/.

Scanning Electron Microscope — Photograph Number 354-1043B

In late 1967, this Stereoscan Mark VI scanning electron microscope (SEM) was delivered to NASA’s Jet Propulsion Laboratory by the Cambridge Instrument Company. They were in high demand at the time, and JPL had to wait nearly a year between placing the order and delivery. It was used by the Electronic Parts Engineering Section Failure Analysis Laboratory to examine microcircuits for defects. Other possible uses were for the study of metals and other materials, and to examine spores for the Capsule Sterilization Program. It used an electron beam to scan the specimen rather than visible light, at a magnification of 20X to 50,000X. The camera on the front right side could be used to record the images.

This post was written for “Historical Photo of the Month,” a blog by Julie Cooper of JPL’s Library and Archives Group.

By Marc Rayman

As NASA’s Dawn spacecraft investigates its first target, the giant asteroid Vesta, Marc Rayman, Dawn’s chief engineer, shares a monthly update on the mission’s progress.

This artist’s concept shows NASA’s Dawn spacecraft orbiting the giant asteroid Vesta. The depiction of Vesta is based on images obtained by Dawn’s framing cameras. Image credit: NASA/JPL-Caltech |
› Full image and caption

Dear Dawnright Spectacular Readers,

Dawn is wrapping up a spectacularly rewarding phase of its mission of exploration. Since descending to its low-altitude mapping orbit (LAMO) in December, the stalwart probe has circled Vesta about 800 times and collected a truly outstanding trove of precious observations of the protoplanet. Having far exceeded the plans, expectations, and even hopes for what it would accomplish when LAMO began, the ambitious explorer is now ready to begin its ascent. On May 1, atop its familiar blue-green pillar of xenon ions, the craft will embark upon the six-week spiral to its second high-altitude mapping orbit.

When the intricate plans for Dawn’s one-year orbital residence at Vesta were developed, LAMO was to be 70 days, longer than any other phase. Because of the many daunting challenges of exploring an uncharted, alien world in the forbidding depths of the asteroid belt so far from home, mission planners could not be confident of staying on a rigid schedule, and yet they wanted to make the most of the precious time at the giant asteroid. They set aside 40 days (with no committed activities) to use as needed in overcoming problems during the unique approach and entry into orbit as well as the intensive observation campaigns in survey orbit and the first high-altitude mapping orbit plus the complex spiral flights from each science orbit to the next. To no one’s surprise, unexpected problems did indeed arise on occasion, and yet in every case, the dedicated professionalism and expertise of the team (occasionally augmented with cortisol, caffeine, and carbohydrates) allowed the expedition to remain on track without needing to draw on that reserve. To everyone’s surprise and great delight, by the beginning of LAMO on December 12, the entirety of the 40 days remained available. Therefore, all of it was used to extend the time the spacecraft would spend at low altitude studying the fascinating world beneath it.

Dawn’s mission at Vesta, exciting and successful though it is, is not the craft’s sole objective. Thanks to the extraordinary capability of its ion propulsion system, this is the first vessel ever planned to orbit two extraterrestrial destinations. After it completes its scrutiny of the behemoth it now orbits, the second most massive resident of the main asteroid belt, Dawn will set sail for dwarf planet Ceres, the largest body between the orbits of Mars and Jupiter.

Since 2009, the interplanetary itinerary has included breaking out of Vesta orbit in July 2012 in order to arrive at Ceres on schedule in February 2015. Taking advantage of additional information they have gained on the spacecraft’s generation and consumption of electrical power, the performance of the ion propulsion system, and other technical issues, engineers have refined their analyses for how long the journey through the asteroid belt to Ceres will take. Their latest assessment is that they can shave 40 days off the previous plan, once again demonstrating the valuable flexibility of ion propulsion, and that translates into being able to stay that much longer at the current celestial residence. (This extension is different from the 40 days described above, because that was designed to ensure Dawn could complete its studies and still leave on schedule in July. For this new extension, the departure date is being changed.) Even though a larger operations team is required at Vesta than during the cruise to Ceres, the Dawn project has the wherewithal to cover the cost. Because operations at Vesta have been so smooth, no new funds from NASA are needed; rather, the project can use the money it had held in reserve in case of problems. In this new schedule, Dawn will gently free itself of Vesta’s gravitational hold on August 26.

Most of the bonus time has been devoted to extending LAMO by a month, allowing the already richly productive investigations there to be even better. (Future logs will describe how the rest of the additional time at Vesta will be spent.) With all sensors fully operational, the robotic explorer has been making the best possible use of its precious time at Vesta, revealing more and more thrilling details of an exotic world deep in the asteroid belt.

› Continue reading Marc Rayman’s Dawn Journal